This post may contain affiliate links, meaning we may make a small commission on items purchased through links in this post at no extra cost to you.
Pattern Overview
The Fall Crown Headband features two mirrored lace columns separated by slipped stitches on a reverse stockinette background. The headband is knitted flat. The pattern is a 4-row repeat.
The first and last 3 stitches form an i-cord edging, that makes the edges look neat and prevents them from curling.
The cast-on and bind-off edges are seamed together forming a decorative twist in the middle. The seam is hidden by the twist and is not visible.
First, you will cast on the required number of stitches. Next, you will knit a long rectangle until you reach your desired length. Then you will bind off the stitches. After that you will seam the edges together to form the twist.
You might also like these patterns:
- Spikelet Headband knitting pattern
- Glass Vase Headband knitting pattern
- Twisted Branches Headband knitting pattern
Size
S (M) L
To fit head circumference: 54-55 (56-57) 58-59cm / 21.25-21.75 (22-22.5) 22.75-23.25in
Width: 10.5cm/ 4.15in.
Gauge
10 x 10 cm (4x4in) = 21sts x 28rows in stockinette stitch after blocking.
Yarn
Drops Daisy in the color almond (mix 13), 1 ball.
Needles
Notions
Tapestry needle, measuring tape, scissors.
Pattern Notes
This pattern uses two types of slipped stitches: with yarn in front and with yarn in back.
All the wrong-side rows are identical.
Abbreviations
k – knit.
p – purl.
sl – slip stitch as if to purl with yarn in front.
sl wyib – slip stitch as if to purl with yarn in back.
k2tog – knit 2 stitches together.
ssk – slip 1 stitch knitwise, slip the next stitch knitwise, return the 2 stitches back to the left needle, knit those 2 stitches together through the back loops.
yo – yarn over.
RS – right side.
WS – wrong side.
*-* – repeat the instructions in between the asterisks the number of times specified.
Save this post for later!
FALL CROWN HEADBAND KNITTING PATTERN
Headband
Cast on 29 stitches.
Set-up row (WS): k5, *p1, k2, p4, k2* two times, p1, k2, sl3.
Row 1 (RS): k3, p2, sl1 wyib, p2, k2tog, yo, k2, p2, sl1 wyib, p2, k2, yo, ssk, p2, sl1 wyib, p2, sl3.
Row 2 (WS): k5, *p1, k2, p4, k2* two times, p1, k2, sl3.
Row 3: k3, p2, sl1 wyib, p2, k2, yo, ssk, p2, sl1 wyib, p2, k2tog, yo, k2, p2, sl1 wyib, p2, sl3.
Row 4: k5, *p1, k2, p4, k2* two times, p1, k2, sl3.
Repeat rows 1-4 until the headband measures 49 (51) 52.5cm/ 19.25 (20) 20.75in.
Bind off sts. Cut the yarn, leaving a 30cm (12″) tail for seaming.
At this step, it is best to wet block the finished headband and lay it flat to dry. Then weave in the cast-on tail.
Twist
Lay the headband flat. The right side should be facing you.
Thread the yarn tail onto a tapestry needle. Fold each end of the headband in half, so they form a “V”.
Place one edge into another, making sure the yarn tail is not in between the layers.
Sew through the four layers of fabric from one end to the other. Go back and forth, making sure you go through all the layers.
Weave in the yarn tail. Turn the headband inside out.
